Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 84

Serial Communication Module

The rack-slot based serial communication module is used to
communicate to serial based controllers. The module can be used to
communicate to Modbus RTU Slave, Modbus RTU Master, Modbus
ASCII Slave, Modbus ASCII Master and user defined protocol type
devices. It contains one Multi-SPI at 4MBps of maximum
communication code rate. Also it supports short circuit protection
and over voltage protection. The galvanic isolation is 2000 VDC.

There are two DB9 connectors for RS232 and a dual-row terminal
connector for RS485 shown in the following figure.

As indicated in this figure, Serial Communication Module includes:

Table 5-10: Serial Communication Module Components

Item Description

1

Module Status LED indicator for the Serial Communication Module. See
"Serial Communication Module Indicators" on page 1 for more information.

2

RS232 LED indicator for the Serial Communication Module. See "Serial
Communication Module Indicators" on page 171 for more information.

3

RS232 Ports (two)

4

RS485 LED indicators for the Serial Communication Module. See "Serial

84

«
...
82
83
84
85
86
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов