Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 94

n

Channel Used: Any one of the channels can be used for Pulse
Output. However, the use of a particular channel for outputting
pulses will render the particular input channel unusable for either
of pulse, frequency or quadrature input.

n

Digital Output Type: Open Collector, 5 to 24V, 30 mA max

n

Frequency Range: 25 Hz – 10 KHz

n

Duty cycle: Always 50%

n

Pulse Output Duration: Selectable CONTINUOUS or NUMBERED
PULSES.

Frequency Input supports:

n

Input Voltage: 0 V DC to 24V DC

n

ON Voltage Level: 3.0 V DC minimum

n

OFF Voltage Level: 1.0 V DC maximum

n

Input Impedance: 25K ohm

n

Frequency: 10 Hz to 100 KHz

n

Minimum Pulse Width: 500 μsec (10 Hz to 500 Hz) ; 50 μsec (10 Hz
to 5 KHz) ; 2.5 μsec (10 Hz to 100 KHz)

l

The input signal will be rejected if it is below a selected pulse
width.

l

The input signal whose pulse width is above the selected pulse
width must be within the frequency range specified, otherwise a
invalid value (NAN) will be shown and a fail-to-convert error
occurs.

n

Digital Output ON if input frequency out of range, else OFF

Quadrature Input Supports:

n

Channel Used: Only channel 1 and 2 can be used for quadrature
pulses A and B respectively. Index pulse is provided in addition.

n

Input Voltage Range: Differential: -6 VDC to +6 VDC; Single-ended:
0 VDC to 24 VDC

n

ON Voltage Level: Differential: 0.2 VDC minimum; Single-ended:
3.0 VDC minimum

n

OFF Voltage Level: Differential: -0.2 VDC maximum; Single-ended:
1 VDC maximum

n

Common Mode Voltage: +/- 12VDC

n

Input Sensitivity: +/- 200mV

n

Hysteresis: +/- 50mV

n

Module powered encoder: 5V DC, 0.50A

n

Frequency: 200 KHz maximum

94

«
...
92
93
94
95
96
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов