Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 44

Control Processor Module

A Redundant Controller Rack contains two CPMs. Either CPM can be
primary.

The CPM is shown in the following figure.

Figure 4-1: Control Processor Module

As indicated in this figure, CPM includes:

Table 4-2: Control Processor Module Components

Item Description

1

Status LED indicator for the CPM.

2

Role LED indicator for the CPM.

3

SD card slot: Reserved for future use.

4

Mode switch

5

Ethernet port 1 (ETH1) and Ethernet port 2 (ETH2) for uplink connectivity to
an Experion FTE network. ETH1 should be connected to the FTE A (yellow) and
ETH2 should be connected to FTE B (green) networks. For more information,
see Experion documentation.

6

Ethernet port 3 (ETH3) and Ethernet port 4 (ETH4) for connectivity to the

44

«
...
42
43
44
45
46
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов