Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 230 | Manualshive

Страница: 230 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 230

For the purpose of submission, a security vulnerability is defined as a
software defect or weakness that can be exploited to reduce the
operational or security capabilities of the software.

Honeywell investigates all reports of security vulnerabilities affecting
Honeywell products and services.

To report a potential security vulnerability against any Honeywell
product, please follow the instructions at:

https://honeywell.com/pages/vulnerabilityreporting.aspx

Submit the requested information to Honeywell using one of the
following methods:

n

Send an email to

[email protected]

; or.

n

Contact your local Honeywell Process Solutions Customer Contact
Center (CCC) or Honeywell Technical Assistance Center (TAC).

Support

For support, contact your local Honeywell Process Solutions
Customer Contact Center (CCC). To find your local CCC visit the
website,

https://www.honeywellprocess.com/en-US/contact-

us/customer-support-contacts/Pages/default.aspx

Training classes

Honeywell holds technical training classes that are taught by process
control systems experts. For more information about these classes,
contact your Honeywell representative, or see

http://www.automationcollege.com

.

230

Appendix A - Installing RTP

«
...
228
229
230

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов