Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 29

29

PLC/RTU" in

ControlEdge PLC and ControlEdge RTU Network and

Security Guide

for more information.

14. Optional-for IPsec enable system, enable the IPsec in the PC

installed the ControlEdge Builder. See "Enable IPsec policy on
PCs" in

ControlEdge PLC and ControlEdge RTU Network and

Security Guide

for more information.

Replacing a secondary PLC-CPM

ATTENTION: Replacing a secondary CPM can be performed
while on-process or off-process.
We recommend that you proceed with extreme caution
whenever replacing any component in a control system. Be
sure the system is offline or in a safe operating mode.
Component replacements may also require firmware update.
Wear an ESD wrist strap and observe static precautions

You will need a #2 Phillips screwdriver.

To replace a secondary PLC-CPM

1. [Optional] It is recommended to disable and prevent

synchronization first by issuing the redundancy disable
synchronization command from ControlEdge Builder.

2. Using an external (user-supplied) switch, disconnect the power

supply in the rack (associated with the CPM to be replaced) from
the source main power.

3. Observe where communications cables are plugged into the CPM

to be replaced, and if necessary, tag them to identify their
functions. Unplug all communications cables.

4. At the top and bottom of the module to be replaced, loosen the

captured screws that secure the module in the rack, and remove
the CPM from the rack. (Note that an up/down rocking motion
helps with removal of the module).

5. At the top and bottom of the module, loosen the captured screws

that secure the module in the rack, and remove the CPM from the
rack.

6. Ensure that the new CPM is properly aligned with the slot guides,

insert the new CPM in the rack, and secure it in place with the
captured screws at top and bottom of the module.

7. Re-install communications cables.

«
...
27
28
29
30
31
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов