Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 51

Страница: 51 / 230

9. Use the Firmware Manager to laod firmware to the new CPM to

match the version that is running in the primary redundant
partner CPM.

10. Check the redundancy synchronization state by monitoring the

role LED of the primary or secondary CPM.

To replace an unsynchronized primary CPM,:

Refer to Replacing a non-redundant UOC-CPM section for this
information.

Following section provides information about replacing EPM, I/O
Module and Spare parts that are common to both PLC and UOC.

Table 4-3: Reference for replacing EPM, I/O Module and Spare parts that are common
to both PLC and UOC

Component
replacement

Reference

EPM

For information about replacing EPM, see the section

EPM

device replacement

I/O Module

For information about replacing I/O Module, see the section

I/O

module replacement

Spare parts

For information about replacing spare parts, see the section

Spare parts

Содержание ControlEdge 900 platform







































































































































































































































Результаты поиска

Содержание ControlEdge 900 platform

Отзывы:

Honeywell ControlEdge 900 platform, Руководство по планированию и установке оборудования, Страница: 51 / 230

Результаты поиска

Содержание ControlEdge 900 platform

Отзывы: