Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 21

21

Item

Component
Name

Description

Source

Switch or
Router/Firewall

100Base-T Ethernet devices in an Ethernet
network. Devices include other
ControlEdge 900 Controller, HMIs, and
includes routers, servers, and other devices
in wider networks. Use of a properly
configured firewall provides a more robust
network limiting exposure to uncontrolled
network traffic.

8

Ethernet CAT5
shielded cable

Connects I/O expansion racks to CPMs
and/or to 100Base-T Ethernet switches.
The maximum length of the Ethernet cable
is 100m.

Third-party
suppliers

Fiber Optics
Cable

The maximum length of multi-mode fiber
optic cable depends on the specification of
network device, typically 5 Km with a MOXA
EDS-308-MM-SC. A qualified Fiber Optic
Convertor is required.

9

Communications
cable

Ethernet able or Fiber Optic Cable
connects devices icn Ethernet Open
Connectivity network to SCADA
applications.

Third-party
suppliers

Following sections provide information about installing racks, EPM,
power supply and so on.

Table 3-3: Reference about installing racks, EPM, power supply and so on

Components

Reference section

Racks

For information about options and types of racks, see the sections

and

. For information about installing

Racks, see the section

Rack Installation

EPM

For information about installing EPM, see the section

Processor Module

.

Power Supply

For information about connecting to AC or DC power supply, see
the section

.

Configuration

For information about configuration, refer to the Software
Configuration Guide.

Environmental

For information about environmental consideration to be taken
care, see the section

Environmental Considerations

.

«
...
19
20
21
22
23
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов