Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 53

Страница: 53 / 230

CHAPTER

CONTROLEDGE 900 COMMON REFERENCE
INFORMATION

This section is applicable to both UOC and PLC systems and provides
the following information:

Installation

Wiring and cabling planning

Maintenance

Diagnostics and Troubleshooting

Special Condition of Use and Approved Standards

Installation

The topics covered in this chapter are:

See "Rack options" below for more information.

See "Rack Types" on page 55 for more information.

See "Rack installation" on page 64 for more information.

See "Power Supply" on page 77 for more information.

See "Environmental considerations" on page 81 for more
information.

See "ControlEdge 900 I/O " on page 87 for more information.

See "Terminal block styles" on page 100 for more information.

See "Terminal Block-to-Field (Signal) Wiring" on page 106 for
more information.

Rack options

I/O racks are available in 4-slot, 8-slot, and 12-slot versions and can
be utilized to house either a controller and I/O or as an I/O expansion
rack containing EPM and I/O.

Both 8-slot I/O rack and 12-slot I/O rack have two types of racks:

Содержание ControlEdge 900 platform







































































































































































































































Результаты поиска

Содержание ControlEdge 900 platform

Отзывы:

Honeywell ControlEdge 900 platform, Руководство по планированию и установке оборудования, Страница: 53 / 230

Результаты поиска

Содержание ControlEdge 900 platform

Отзывы: