Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 160

Страница: 160 / 230

For AC: L1, L2 /N and Ground

For DC: 24V DC +, 24V DC – and Ground

7. Ensure power can be applied safely, and use the external (user-

supplied) switch to re-connect power to the power supply.

8. If the AC power supply is used, using a meter and the test points

on the face of the power supply, ensure that voltages (measured
on the backplane) are within specifications.

Replacing an EPM

CAUTION: Explosion hazard. Removal and Insertion Under Power
is not supported in Division 2/ Zone 2.

You will need a #2 Phillips screwdriver.

To replace an EPM:

1. If a process is currently in operation, then do one of the following

two methods:

Ensure that removing the EPM will not have adverse
consequences on any running process.

Bring the process to a safe and orderly shutdown.

2. Observe where communications cables are plugged into the EPM

to be replaced, and if necessary, tag them to identify their
functions. Unplug the communication cable(s) from the Ethernet
port(s).

3. At the top and bottom of the EPM, loosen the captured screws

that secure the module in the rack, and remove the module from
the rack. (Note that an up/down rocking motion helps with
removal of the module.)

4. Configure the EPM address rotary switches on the replacement

module to match those of the removed module.

5. Ensure that the new EPM is properly aligned with the slot guides,

insert the new EPM in the rack, and secure it in place with the
captured screws at top and bottom of the module.

6. Re-install the communication cable(s).
7. Check status indicators at the EPM, CPM, and I/O modules.
8. Load firmware to the new EPM which is the same version as was

running in the removed module.

160

Содержание ControlEdge 900 platform







































































































































































































































Результаты поиска

Содержание ControlEdge 900 platform

Отзывы:

Honeywell ControlEdge 900 platform, Руководство по планированию и установке оборудования, Страница: 160 / 230

Результаты поиска

Содержание ControlEdge 900 platform

Отзывы: