Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 89

89

I/O Module Specification

ControlEdge PLC supports various input/output modules. This
section provides technical information to configure ControlEdge PLC
IO Modules. The following IO modules are included:

n

Universal Input/output module, 16 channel

n

Universal AI – RTD,TC,V 8 Channel

n

Analog Input High Level, 16 Channel

n

Analog Output, 4 Channel

n

Analog Output, 8 Channel

n

Digital Input 120/240 VAC, 16 Channel

n

Digital Input 24 VDC, 32 Channel

n

Digital Input Contact, 16 Channel

n

Digital Input 120/240 VAC, 125 VDC (16 Channel Isolated)

n

Digital Output 120/240 VAC, 16 Channel

n

Digital Output 24 VDC, 32 Channel

n

Digital Relay Output, 8 Channel

n

Pulse/Frequency/Quadrature, 4 Channel

See ControlEdge PLC Specification for details.

Universal Input/Output Module

The maximum current of the Universal Input/Output Module (UIO)
field side is 4.2 A.

One UIO module provides a 20-terminal block with 16 channels, and
it can be connected with two external 24 V DC power supplies. At least
one power supply must be connected.

See

UIO module wiring

section.

UIO module supports:

n

16 Channel, each channel can be configured for AI, AO, DI & DO

l

Analog Input (AI), 0-20 mA

l

Analog Input (AI) with open wire detection, 4-20 mA

l

Analog Output (AO), 4-20 mA, See

Field wiring for Analog

section for channel restrictions on the same UIO

module.

l

Digital Input (DI) with line monitoring

l

Digital Output (DO) with short circuit protection

«
...
87
88
89
90
91
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов