Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 230

Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 116

side of the wire-pair.

n

Voltage input: This is because UIO supports only current
measurements.

n

Slide wire: This is because UIO supports only current
measurements.

Allowable field wiring resistance - UIO - Analog Input
channel

The maximum allowable field wiring resistance between the
transmitter and the connection terminal is dependent upon the
voltage requirement of the transmitter. The formula for calculating
the maximum wiring resistance for the UIO channel used as an
analog input is given by the following equation:

Rmax= [(19.0-Vtx) / (0.022)]

Where, Vtx=Voltage required at the transmitter terminal.

Field wiring for Analog Output

The UIO can drive 4-20mA. See the following list for AO specification:

n

No load restrictions: 6 channels with no other channels
configured.

n

With load restrictions:

o

channels into 250 ohm load with no other channels configured.

o

channels into 250 ohms remaining channels may be
configured for 1 DO and up to 10 digital inputs.

o

6 channels into 100 ohms with no other channels configured.

Table 5-16: UIO for Analog Output Specification

Item

Description

Field (loop) resistance

Minimal 100 ohm

D-A conversion

12 bit

Accuracy

< 0.5% of full scale including linearity

Figure 5-27: Field wiring for analog output

116

«
...
114
115
116
117
118
...
»

Содержание ControlEdge 900 platform







































































































































































































































Отзывы:

Нет отзывов