HONDA marine BF25D Скачать руководство пользователя страница 43

Страница: 43 / 141

BEFORE OPERATION

Safety Inspection

• Before each use, look around and

underneath the engine for signs of

oil or gasoline leaks.

• If you are using the portable fuel

tank, make sure it is in good

condition and properly secured in

the boat (p. 45).

• Check that the fuel hose is

undamaged and properly connected

(p. 45).

• Wipe up any spills before starting

the engine.

• Check the stern bracket to be sure

the outboard motor is securely

installed.

• Check that all controls are

operating properly.

• Replace any damaged parts.

• Check that all fasteners are in place

and securely tightened.

• Check the emergency stop switch

for proper operation. Start the

engine (p. 47, 49 or 54). Make sure

the engine stops by pulling the

emergency stop switch clip from

the emergency stop switch.

Maintenance Inspection

• Check the engine oil level (p. 72).

Running the engine with a low oil

level can cause engine damage.

Overfilling the engine can cause

the engine to smoke or have oil

leaks which can cause engine

damage.

• Check to be sure the propeller is

undamaged and the castle nut is

secured with the cotter pin (p. 86).

• Check that the stern bracket anode

and the trim tab are securely

attached and are not excessively

worn. The anodes help to protect

the outboard motor from corrosion.

• Make sure the tool kit and

emergency starter rope are onboard

(p. 67). Replace any missing items.

• Check the fuel level in the fuel tank

(p. 79).

• Check that the battery fluid is

between the upper and lower

levels, and the battery leads are

connected securely.

31ZW26430.book Page 41 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды