HONDA marine BF25D Скачать руководство пользователя страница 48

Страница: 48 / 141

OPERATION

Connect the fuel hose to the tank and

the outboard motor, as shown. Be

sure both connectors snap securely

into place. Always disconnect the

fuel hose when storing or transporting

the outboard motor.

FUEL PRIMING

If you are using a portable fuel tank,

turn the portable fuel tank vent knob

counterclockwise to the open

position.

Hold the fuel priming bulb with the

outlet end higher than the inlet end.

Squeeze the priming bulb several

times, until it feels firm, indicating

that fuel has reached the carburetor.

Check to be sure there are no fuel

leaks before starting the engine.

Do not touch the priming bulb with

the engine running or when tilting up

the outboard motor. The carburetors

could overflow.

INFREQUENT OR

OCCASIONAL USE

If your outboard motor will be used

on an infrequent or intermittent basis,

please refer to the fuel section of the

STORAGE

chapter (p. 91) for

additional information regarding fuel

deterioration.

OUTLET END

(outboard motor side)

FUEL PRIMING

BULB

INLET END

(fuel tank side)

31ZW26430.book Page 46 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды