HONDA marine BF25D Скачать руководство пользователя страница 102

Страница: 102 / 141

100

TAKING CARE OF UNEXPECTED PROBLEMS

ENGINE WILL NOT START

Possible Cause

Correction

Out of fuel.

Refuel (p. 79).

Fuel vent closed (portable fuel tank).

Open the vent knob (p. 33).

Fuel hose not primed.

Squeeze priming bulb (p. 46).

Fuel filter or fuel tank filter clogged.

Replace fuel filters (p. 82 and 85).

Bad fuel; outboard motor stored without treating or

draining gasoline, or refueled with bad gasoline.

Drain fuel tank and carburetors (p. 92 and 93). Refill

with fresh gasoline (p. 79).

Spark plugs faulty, fouled, or improperly gapped.

Gap or replace spark plugs (p. 77).

Spark plugs wet with fuel (flooded engine).

Dry and reinstall spark plugs. Start engine with the

throttle open.

Carburetor malfunction, fuel pump failure, ignition

malfunction, stuck valves, etc.

Take outboard motor to an authorized Honda Marine

dealer, or refer to the shop manual.

31ZW26430.book Page 100 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды