HONDA marine BF25D Скачать руководство пользователя страница 105

Страница: 105 / 141

103

TAKING CARE OF UNEXPECTED PROBLEMS

BATTERY WILL NOT

CHARGE AND ELECTRIC

STARTER WILL NOT

OPERATE

The battery-charging circuit and the

electric starter relay circuit are

protected by the 15-ampere fuse. If

the fuse burns out, the engine will not

charge the battery, and the electric

starter will not operate. The engine

can be started using the emergency

starter rope.

The ignition switch is protected by

the 10-ampere fuse. If the fuse burns

out, the engine will not start or run,

and the power trim/tilt switch will not

operate.

Fuse Replacement

1. With the engine stopped, remove

the engine cover (p. 71).

2. Remove the fuse cover.

3. Remove and inspect the fuse. If a

fuse is burnt out, install a

replacement fuse of the specified

rating. The outboard motor is

supplied with a spare fuse in each

fuse holder.

DESIGNATED FUSE RATING:

15A, 10A

Never use a fuse with a rating

greater than specified. Serious

damage to the electrical system

could result.

4. Reinstall the fuse cover and the

engine cover.

Before further operation, try to

determine and correct the electrical

problem that caused the fuse to burn

out. An uncorrected electrical

problem may cause the fuse to burn

out again.

FUSE COVER

15A FUSE

SPARE 15A FUSE

10A FUSE

FUSE COVER

SPARE 10A FUSE

BLOWN FUSE

31ZW26430.book Page 103 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды