HONDA marine BF25D Скачать руководство пользователя страница 97

Страница: 97 / 141

TRANSPORTING

WITH OUTBOARD MOTOR

INSTALLED ON BOAT

When trailering a boat with the

outboard motor attached, always

disconnect the fuel line from the

portable fuel tank.

SHG and LHG Types

(long tiller handle)

Tighten the steering friction adjuster

to prevent the outboard motor from

moving while trailering the boat.

LRG, SRT and LRT Types

(remote control)

Use an outboard motor support bar to

prevent the outboard motor from

moving while trailering the boat.

Refer to the manufacturer’s

instructions for using an outboard

motor support bar.

All Types

The preferred method is to leave the

engine in the normal running

position, but if there is insufficient

road clearance, you can tilt the

outboard motor using a commercially

available outboard motor support bar

available through your dealer. Refer

to the manufacturer’s instructions for

using an outboard motor support bar.

STEERING FRICTION ADJUSTER

TO INCREASE

FRICTION

(LOCK)

TO DECREASE

FRICTION

(FREE)

OUTBOARD MOTOR SUPPORT BAR

(commercially available)

31ZW26430.book Page 95 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды