HONDA marine BF25D Скачать руководство пользователя страница 29

Страница: 29 / 141

CONTROLS AND FEATURES

Manual Relief Valve

(SRT and LRT types)

The outboard motor can also be tilted

manually after opening the manual

relief valve. This feature enables the

outboard motor to be tilted up or

down when no battery is connected.

Check that nobody is under the

outboard motor before opening the

manual relief valve. If the manual

relief valve is loosened (turned

counterclockwise) when the outboard

motor is tilted up, the outboard motor

will suddenly tilt down.

Common Controls

Tilt Lock Lever

The tilt lock lever is used to support

the outboard motor in the fully-raised

position.

When the boat is to be moored for a

long time, tilt the outboard motor up

as far as it will go. Then move the tilt

lock lever to the LOCK position, and

gently lower the outboard motor until

the lever contacts the stern bracket.

Engine Cover Latches

The engine cover latches fasten the

engine cover to the outboard motor.

RIGHT STERN BRACKET

MANUAL RELIEF VALVE

POWER

(To fix)

MANUAL

(To release)

FREE

LOCK

TILT LOCK

LEVER

REAR

FRONT

ENGINE COVER

LATCH

UNLATCH

FIX

31ZW26430.book Page 27 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды