HONDA marine BF25D Скачать руководство пользователя страница 84

Страница: 84 / 141

SERVICING YOUR OUTBOARD MOTOR

Fuel Filter Inspection and

Replacement

The fuel filter is located under the

engine cover between the fuel

coupling and the fuel pump.

Water or sediment accumulation in

the filter can cause loss of power or

hard starting. To prevent engine

malfunction, inspect the filter and

replace when necessary.

1. Disconnect the fuel hose connector

from the outboard motor.

2. Remove the engine cover (p. 71).

Gasoline is highly flammable and

explosive.

You can be burned or seriously

injured when handling fuel.

• Stop the engine and let it cool

before handling fuel.

• Keep heat, sparks, and flame

away.

• Handle fuel only outdoors.

• Keep away from your vehicle.

• Wipe up spills immediately.

PULL

PUSH

FUEL HOSE CONNECTOR

31ZW26430.book Page 82 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды