HONDA marine BF25D Скачать руководство пользователя страница 73

Страница: 73 / 141

SERVICING YOUR OUTBOARD MOTOR

MANUAL RELIEF VALVE

SRT and LRT Types

The outboard motor can be tilted

manually after opening the manual

relief valve. This feature enables the

outboard motor to be tilted when no

battery is connected.

For manual tilting, use a flat blade

screwdriver to turn the valve

counterclockwise 2 and a half turns.

Close the valve firmly after

positioning the engine.

Be sure the valve is closed before

operating the outboard motor. If the

valve is not closed, the outboard

motor will tilt up when operated in

reverse.

ENGINE COVER REMOVAL

AND INSTALLATION

The engine cover latch fastens the

engine cover to the outboard motor.

To remove the engine cover, unlatch

the engine cover latch, then lift the

engine cover off the outboard motor.

To install the engine cover, place the

cover on the outboard motor, then

latch the engine cover latch securely.

MANUAL RELIEF VALVE

RIGHT STERN BRACKET

POWER

(To fix)

MANUAL

(To release)

(REAR)

ENGINE COVER

LATCH

UNLATCH

FIX

(FRONT)

ENGINE

COVER

31ZW26430.book Page 71 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды