HONDA marine BF25D Скачать руководство пользователя страница 86

Страница: 86 / 141

SERVICING YOUR OUTBOARD MOTOR

7. Install the new fuel filter so the

arrow on the filter points toward

the fuel pump.

Fuel flow will be reduced if the

filter is installed backward.

8. Connect the fuel hoses to the fuel

filter securely with the hose

clamps. Remove the fuel hose clips

used to close the fuel hoses.

9. Securely connect the fuel hose

connector to the outboard motor

(p. 45).

10. Prime the engine using the

priming bulb (p. 47). Check for

fuel leaks. Repair any fuel leaks if

necessary.

11. Reinstall the engine cover (p. 71).

If loss of power or hard starting are

found to be caused by excessive

water or sediment accumulation in

the fuel filter, inspect the fuel tank.

Clean the fuel tank and tank filter if

necessary. It may be necessary to

drain the fuel tank completely and

refill with fresh gasoline.

Portable Fuel Tank and Tank

Filter Cleaning

[standard equipment (Canadian

types)]

[optional equipment (American

types)]

HOSE CLAMPS

FUEL PUMP

FUEL FILTER

ARROW

(fuel flow direction)

Gasoline is highly flammable and

explosive.

You can be burned or seriously

injured when handling fuel.

• Stop the engine and let it cool

before handling fuel.

• Keep heat, sparks, and flame

away.

• Handle fuel only outdoors.

• Keep away from your vehicle.

• Wipe up spills immediately.

31ZW26430.book Page 84 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды