HONDA marine BF25D Скачать руководство пользователя страница 90

Страница: 90 / 141

CLEANING AND FLUSHING

Cleaning and Flushing

After each use in salt water or dirty

water, thoroughly clean and rinse the

outboard motor with fresh water.

Touch up any damaged paint, and

coat areas that may rust with Honda

Corrosion Inhibitor, or equivalent.

Lubricate controls with a silicone

spray lubricant.

Do not apply water or corrosion

inhibitor directly to the timing belt

under the engine cover. If water or

corrosion inhibitor penetrates the

timing belt, it may be damaged.

Before applying a corrosion inhibitor,

cover the timing belt with a protective

material to prevent damage.

Cleaning

Wash the outside of the outboard

motor with clean, fresh water, and

flush the cooling system as described.

Flushing With the Honda

Garden Hose Adapter (optional

equipment)

It is necessary to run the engine

during the flushing procedure. For

safety, remove the propeller from the

outboard motor (p. 86).

1. Tilt down the outboard motor.

2. Remove the wash screw and

sealing washer from the WASH

screw hole in the gear case. Be sure

not to remove the oil level screw

from the OIL LEVEL screw hole in

the gear case.

WASH SCREW (flush screw)

31ZW26430.book Page 88 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды