HONDA marine BF25D Скачать руководство пользователя страница 75

Страница: 75 / 141

SERVICING YOUR OUTBOARD MOTOR

When you check the oil level with the dipstick, you might notice the engine oil

appears milky or the oil level has increased. If you notice either condition,

change the engine oil. See the following table for an explanation of these

conditions.

Operating Method

Result

Effect

Running the engine below
3,000 rpm for more than
30% of the time so the
engine does not warm up.

• Water condenses in the

engine and mixes with the
oil, resulting in a milky
appearance.

The engine oil deteriorates,
becomes less efficient as a
lubricant, and causes an
engine malfunction.

Frequent starting and
stopping without allowing
the engine to warm up.

• Unburned fuel mixes with

the oil, increasing the
volume of oil.

Engine Oil Change

An engine oil evacuation device may

be used to remove the engine oil.

Drain the used oil while the engine is

warm. Warm oil drains quickly and

completely.

1. Unlatch and remove the engine

cover (p. 71). Remove the oil filler

cap (p. 72).

31ZW26430.book Page 73 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды