HONDA marine BF25D Скачать руководство пользователя страница 74

Страница: 74 / 141

SERVICING YOUR OUTBOARD MOTOR

Engine Oil Level Check

Check the engine oil level with the

engine stopped and the outboard

motor in the vertical position.

1. Unlatch and remove the engine

cover (p. 71).

2. Remove the oil level dipstick and

wipe it clean.

3. Insert the dipstick all the way in,

then remove it and check the oil

level shown on the dipstick.

4. If the oil level is low, remove the

oil filler cap, and add oil to reach

the upper limit mark shown on the

dipstick. Use the oil recommended

on p. 75.

• Running the engine with a low

oil level can cause engine

damage.

• Do not overfill. Overfilling the

engine will cause it to smoke or

have oil leaks.

5. Install the oil filler cap and tighten

it securely.

6. Install and lock the engine cover.

OIL LEVEL DIPSTICK

UPPER

LIMIT

LOWER

LIMIT

OIL FILLER CAP

31ZW26430.book Page 72 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды