HONDA marine BF25D Скачать руководство пользователя страница 83

Страница: 83 / 141

SERVICING YOUR OUTBOARD MOTOR

FUEL RECOMMENDATIONS

This engine is certified to operate on

unleaded gasoline with a pump

octane rating of 86 or higher.

You may use unleaded gasoline

containing no more than 10% ethanol

(E10) or 5% methanol by volume. In

addition, methanol must contain

cosolvents and corrosion inhibitors.

Use of fuels with content of ethanol

or methanol greater than shown

above may cause starting and/or

performance problems. It may also

damage metal, rubber, and plastic

parts of the fuel system.

Engine damage or performance

problems that result from using a fuel

with percentages of ethanol or

methanol greater than shown above

are not covered under warranty.

Never use gasoline that is stale,

contaminated, or mixed with oil.

Avoid getting dirt or water in the fuel

tank.

If your outboard motor will be used

on an infrequent or intermittent basis,

please refer to the fuel section of the

STORAGE

chapter (p. 91) for

additional information regarding fuel

deterioration.

31ZW26430.book Page 81 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды