HONDA marine BF25D Скачать руководство пользователя страница 95

Страница: 95 / 141

STORAGE

6. Repeat this procedure to drain # 3

carburetor.

7. After all three carburetors are

drained, reinstall the drain tube on

# 1 carburetor.

8. Reinstall the engine cover (p. 71).

9. Drain the fuel tank into an

approved gasoline container, or if

you need to store fuel in the fuel

tank, you can extend fuel storage

life by filling the fuel tank with

fresh gasoline and adding Honda

Marine fuel stabilizer following the

directions on the container. Close

the fuel cap vent.

If using the portable fuel tank,

close the fuel filler cap vent knob.

Store the portable fuel tank in a

cool dry place out of direct

sunlight.

Engine Oil

1. Change the engine oil (p. 73).

2. Remove the spark plugs (p. 77),

and remove the emergency stop

switch clip from the emergency

stop switch.

3. Pour 1 – 2 teaspoons (5 – 10 cm

)

of clean engine oil into each

cylinder.

4. Using the emergency starter rope

(p. 52), rotate the flywheel a few

revolutions to distribute the oil in

the cylinders.

5. Reinstall the spark plugs (p. 78).

STORAGE PRECAUTIONS

Select a well-ventilated storage area.

If possible, avoid storage areas with

high humidity.

If storing a container of gasoline,

such as the portable fuel tank, store it

away from any appliance that

operates with a flame, such as a

furnace, water heater, or clothes

dryer. Also avoid any area with a

spark producing electric motor, or

where power tools are operated.

OUTBOARD MOTOR STAND

(commercially available)

31ZW26430.book Page 93 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды