HONDA marine BF25D Скачать руководство пользователя страница 58

Страница: 58 / 141

OPERATION

2. Turn the ignition switch key to the

OFF position to stop the engine. In

the event that the engine does not

stop when the ignition switch key

is turned to the OFF position, pull

the emergency stop switch clip out

of the emergency stop switch by

pulling the emergency stop switch

lanyard (p. 54).

3. When the boat is not in use, remove

and store the ignition switch key

and the emergency stop switch clip

and lanyard. If you are using a

portable fuel tank, disconnect the

fuel hose if you will be storing or

transporting the outboard motor.

GEARSHIFT AND

THROTTLE OPERATION

SHG and LHG Types

(long tiller handle)

To shift gears, turn the throttle grip to

the SLOW position; then move the

gearshift lever to select the F

(forward), N (neutral), or R (reverse)

gears.

The engine can be started with the

gearshift lever in the N (neutral)

position only.

The throttle grip can be turned to the

FAST position only when the

gearshift lever is in the F (forward)

position.

POINTER

THROTTLE

GRIP

SLOW

FAST

(neutral)

(reverse)

(forward)

GEARSHIFT

LEVER

31ZW26430.book Page 56 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды