HONDA marine BF25D Скачать руководство пользователя страница 91

Страница: 91 / 141

CLEANING AND FLUSHING

3. Cover the three water intakes with

duct tape as shown above.

4. Remove the sealing washer from

the wash screw and install the

sealing washer on the flush kit

coupler.

5. Install the flush kit coupler into the

WASH screw hole and connect a

fresh water hose to the garden hose

adapter.

6. Move the gearshift lever or control

lever to the N (neutral) position.

Flush the outboard motor in the

neutral position only.

7. Turn on the fresh water supply to

the flush kit coupler.

Running the engine without good

water circulation can cause

overheating and water pump

damage.

Damage caused by running the

outboard motor without sufficient

cooling water is not covered by the

Distributor’s Limited Warranty

(p. 121).

8. Start the engine. Monitor the

cooling system indicator. Stop the

engine if water does not come out

of the cooling system indicator and

check the fresh water supply.

WATER INTAKES

GARDEN HOSE ADAPTER

(FLUSH KIT COUPLER)

COOLING SYSTEM INDICATOR

31ZW26430.book Page 89 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды