HONDA marine BF25D Скачать руководство пользователя страница 87

Страница: 87 / 141

SERVICING YOUR OUTBOARD MOTOR

Fuel Tank

Empty the portable fuel tank into an

approved gasoline container. Use a

funnel to avoid spilling fuel. Rinse

the fuel tank with nonflammable

solvent to remove any accumulated

sediment.

Fuel Tank Filter

1. Remove the four 5 mm screws

using a flat screwdriver, then

remove the fuel hose connector and

fuel tank filter from the tank.

2. Clean the filter in nonflammable

solvent. Inspect the fuel tank filter

and the connector gasket. Replace

them if damaged.

3. Reinstall the filter and hose

connector in the fuel tank. Tighten

the four 5 mm screws securely.

Anode Replacement

FUEL HOSE

(Standard equipment)

5 mm SCREWS (4)

CONNECTOR

GASKET

FUEL TANK

FILTER JOINT

(Fuel Hose Connector)

FUEL TANK

FILTER

ANODE

(trim tab)

ANODE

LEFT STERN BRACKET

31ZW26430.book Page 85 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды