HONDA marine BF25D Скачать руководство пользователя страница 81

Страница: 81 / 141

SERVICING YOUR OUTBOARD MOTOR

REFUELING

If you do not anticipate cycling

through at least one complete tank of

fuel within a 30 day period, we

recommend adding Honda Marine

Fuel Stabilizer each time you refuel.

Portable Fuel Tank

[standard equipment

(Canadian types)]

[optional equipment (American

types)]

FUEL TANK CAPACITY:

6.6 US gal (25 L)

Check the fuel gauge and refill the

tank when necessary.

Remove the fuel tank from the boat

for refueling.

1. Turn the vent knob

counterclockwise to the OPEN

position.

2. Turn the fuel filler cap

counterclockwise so that it touches

the pressure relief tab.

3. Press down the pressure relief tab,

and then turn the fuel filler cap 1/4

counterclockwise. Release the

pressure relief tab. Wait to relieve

pressure.

4. The fuel filler cap will lock again.

Press down the pressure relief tab,

and turn counterclockwise to

remove the fuel filler cap.

FUEL GAUGE

VENT KNOB

OPEN

FUEL FILLER CAP

PRESSURE RELIEF TAB

FUEL FILLER CAP

PRESS

PRESSURE RELIEF TAB

31ZW26430.book Page 79 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды