HONDA marine BF25D Скачать руководство пользователя страница 94

Страница: 94 / 141

STORAGE

Draining the Fuel System

You can avoid fuel deterioration

problems by draining the fuel tank

and carburetors.

1. Disconnect the fuel hose connector

from the outboard motor (p. 82).

2. Remove the engine cover (p. 71).

3. With the outboard motor in a

vertical position, place an approved

gasoline container below the fuel

drain outlet, and use a funnel to

avoid spilling fuel.

4. Loosen the drain screw on # 1

carburetor, allow the carburetor to

drain completely, then tighten the

drain screw securely.

5. Remove the drain tube from # 1

carburetor, install it on # 2

carburetor, and drain that

carburetor in the same manner.

DRAIN SCREWS

Gasoline is highly flammable and

explosive.

You can be burned or seriously

injured when handling fuel.

• Stop the engine and let it cool

before handling fuel.

• Keep heat, sparks, and flame

away.

• Handle fuel only outdoors.

• Keep away from your vehicle.

• Wipe up spills immediately.

DRAIN TUBE

# 1 CARBURETOR

DRAIN SCREW

# 2 CARBURETOR

DRAIN SCREW

# 3 CARBURETOR

DRAIN SCREW

31ZW26430.book Page 92 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды