HONDA marine BF25D Скачать руководство пользователя страница 69

Страница: 69 / 141

SERVICING YOUR OUTBOARD MOTOR

SPARE SWITCH CLIP (long

tiller handle type) AND

EMERGENCY STARTER

ROPE

Always carry the spare switch clip

and the emergency starter rope

onboard. The spare clip may either be

stored in the tool bag or in an easily

accessible location on the boat along

with the emergency starter rope.

SPARE SWITCH CLIP

(long tiller handle type)

EMERGENCY STARTER ROPE

TOOL KIT

Individual items in the tool kit shown above can be purchased from an

authorized Honda Marine dealer and may be used for simple maintenance

procedures and/or emergency repairs. Keep this tool kit or an equivalent

onboard, so that they will always be available if you need them.

If your tool kit needs replacement, it is not available as a kit and each item

must be ordered individually.

8 × 10 mm WRENCH

FLAT SCREWDRIVER

GRIP

18 × 19 mm SOCKET WRENCH

TOOL BAG

31ZW26430.book Page 67 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды