HONDA marine BF25D Скачать руководство пользователя страница 51

Страница: 51 / 141

OPERATION

During the warm-up period, check

the oil pressure indicator (p. 30),

overheat indicator (p. 31) and

cooling system indicator (p. 31).

If the indicators show any

abnormal condition, immediately

stop the engine and determine the

cause of the problem. Refer to

TAKING CARE OF

UNEXPECTED PROBLEMS

p. 104.

LRG, SRT and LRT Types

(remote control)

For panel-mount or top-mount remote

control information, refer to the

instructions provided with the remote

control equipment.

Side-Mount Type

[standard equipment (LRTC

type)]

[optional equipment (LRGA,

SRTA and LRTA types)]

1. Put the emergency stop switch clip

in the emergency stop switch, and

attach the emergency stop switch

lanyard securely to the operator or

to the operator’s PFD (Personal

Flotation Device).

The engine will not start or run

unless the emergency stop switch

clip is in the emergency stop

switch.

The emergency stop switch clip

and emergency stop switch lanyard

system is a safety device that will

stop the engine if you fall away

from the controls while operating

the boat.

Always attach the emergency stop

switch lanyard securely to the

operator or to the operator’s PFD

before starting the engine.

Before leaving the dock, check the

operation of the emergency stop

switch.

EMERGENCY

STOP SWITCH

EMERGENCY STOP

SWITCH CLIP

EMERGENCY

STOP SWICH

LANYARD

31ZW26430.book Page 49 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды