HONDA marine BF25D Скачать руководство пользователя страница 106

Страница: 106 / 141

104

TAKING CARE OF UNEXPECTED PROBLEMS

OIL PRESSURE INDICATOR

GOES OFF AND ENGINE

SPEED IS LIMITED

If oil pressure becomes low, the green

indicator will go off, and the engine

protection system will limit engine

speed. If you are at cruising speed,

engine speed will decrease

automatically.

Remote control type is equipped with

a buzzer that sounds continuously

when the green indicator goes off.

The buzzer sound stops below an

engine speed of 1,400 rpm.

Low oil pressure may be the result of

a low engine oil level, or there may

be a problem with the engine

lubrication system.

If the throttle is closed suddenly after

full throttle operation, engine speed

may drop below the specified idle

rpm, and that could activate the

engine protection system

momentarily.

If low oil pressure activates the

engine protection system, stop the

engine, check the engine oil level

(p. 72), and add oil if needed.

With the engine oil at the

recommended level, restart the

engine. If the lubrication system is

OK, the green indicator light should

come on within 30 seconds, and the

engine will respond normally to

throttle grip or control lever

operation.

If the engine protection system

remains activated after 30 seconds,

return to the nearest boat landing, and

have the outboard motor inspected by

an authorized Honda Marine dealer.

SHG and LHG Types

(long tiller handle)

LRG, SRT and LRT Types

[remote control (side-mount

type)]

(GREEN)

BUZZER

31ZW26430.book Page 104 Monday, November 19, 2018 4:42 PM

Содержание BF25D












































































































































Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды

HONDA marine BF25D, Руководство пользователя

Результаты поиска

Содержание BF25D

Отзывы:

Бренды по названию

Популярные бренды