H3C S5120-EI Series Скачать руководство пользователя страница 76

Страница: 76 / 242

MAC Information configuration commands

NOTE:

MAC Information applies only to Layer 2 Ethernet interfaces.

MAC Information configuration commands

mac-address information enable (Ethernet interface view)

Syntax

mac-address information enable

{

added

deleted

}

undo mac-address information enable

{

added

deleted

}

View

Layer 2 Ethernet interface view

Default level

1: Monitor level

Parameters

added

: Enables the device to record security information when a new MAC address is learned on the

Ethernet port.

deleted

: Enables the device to record security information when an existing MAC address is deleted.

Description

Use the

mac-address information enable

command to enable MAC Information on the Layer 2 Ethernet

interface.
Use the

undo mac-address information enable

command to disable MAC Information on the Layer 2

Ethernet interface.
By default, MAC Information is disabled on a Layer 2 Ethernet interface.
This command is not supported on aggregate interfaces.
To enable MAC Information on an Ethernet interface, enable MAC Information globally first.

Examples

# Enable MAC Information on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface GigabitEthernet1/0/1

[Sysname-GigabitEthernet1/0/1] mac-address information enable added

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды