manualshive.com logo in svg

H3C S5120-EI Series, Справочник по командам

Поделиться
Скачать
H3C S5120-EI Series Скачать руководство пользователя страница 57

45 

Description 

Use the 

virtual-cable-test 

command to test the cable connection of an Ethernet interface. The test results 

are displayed within five seconds. 
The following cable states are available:  

•

 

Normal

—

The cable is in good condition.  

•

 

Abnormal

—

Any fault other than a short or open circuit is detected.  

•

 

Abnormal (open)

—

An open circuit is detected. 

•

 

Abnormal (short)

—

A short circuit is detected. 

•

 

Failure

—

The detection fails.  

If the cable connection is normal, the displayed cable length is the total length of the cable.  
If the cable connection has a fault, it is the length from the local port to the faulty point. 

 

 

NOTE: 

•

 

Optical interfaces do not support this command. 

•

 

If the link of an Ethernet interface is up, testing its cable connection will cause the link to go down and
then up. 

•

 

The test result is for reference only. The cable length detection error is up to 5 m (about 16 ft). If a test item
is not available, a hyphen (-) is displayed. 

 

Examples 

# Test the cable connection of interface GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] virtual-cable-test 

Cable status: normal, 1 metres 

Pair Impedance mismatch: - 

Pair skew: - ns 

Pair swap: - 

Pair polarity: - 

Insertion loss: - db 

Return loss: - db 

Near-end crosstalk: - db 

 

 

NOTE: 

The 

Pair Impedance mismatch

 field takes two values: yes for match, and no for mismatch. 

 

Содержание S5120-EI Series



















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды