H3C S5120-EI Series Скачать руководство пользователя страница 145

Страница: 145 / 242

133

BPDU tunneling configuration commands

bpdu-tunnel dot1q

Syntax

In Ethernet interface view or port group view:

bpdu-tunnel dot1q

{

cdp

dldp

eoam

gvrp

hgmp

lacp

lldp

pagp

pvst

stp

udld

vtp

}

undo bpdu-tunnel dot1q

{

cdp

dldp

eoam

gvrp

hgmp

lacp

lldp

pagp

pvst

stp

udld

vtp

}

In Layer 2 aggregate interface view:

bpdu-tunnel dot1q

{

cdp

gvrp

hgmp

pvst

stp

vtp

}

undo bpdu-tunnel dot1q

{

cdp

gvrp

hgmp

pvst

stp

vtp

}

View

Ethernet interface view, port group view, Layer 2 aggregate interface view

Default level

2: System level

Parameters

cdp

: Enables BPDU tunneling for the Cisco Discovery Protocol (CDP).

dldp

: Enables BPDU tunneling for the Device Link Detection Protocol (DLDP).

eoam

: Enables BPDU tunneling for Ethernet Operation, Administration and Maintenance (EOAM).

gvrp

: Enables BPDU tunneling for the GARP VLAN Registration Protocol (GVRP).

hgmp

: Enables BPDU tunneling for the HW Group Management Protocol (HGMP).

lacp

: Enables BPDU tunneling for the Link Aggregation Control Protocol (LACP).

lldp

: Enables BPDU tunneling for the Link Layer Discovery Protocol (LLDP).

pagp

: Enables BPDU tunneling for the Port Aggregation Protocol (PAGP).

pvst

: Enables BPDU tunneling for Per VLAN Spanning Tree (PVST).

stp

: Enables BPDU tunneling for the Spanning Tree Protocol (STP).

udld

: Enables BPDU tunneling for Uni-directional Link Direction (UDLD).

vtp

: Enables BPDU tunneling for the VLAN Trunking Protocol (VTP).

Description

Use the

bpdu-tunnel dot1q

command to enable BPDU tunneling for a protocol on the port or ports.

Use the

undo bpdu-tunnel dot1q

command to disable BPDU tunneling for a protocol on the port or ports.

By default, BPDU tunneling for any protocol is disabled.

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды