H3C S5120-EI Series Скачать руководство пользователя страница 131

Страница: 131 / 242

119

stp mode

Syntax

stp mode

{

stp

rstp

mstp

}

undo stp mode

View

System view

Default level

2: System level

Parameters

stp

: Configures the MSTP-enabled switch to work in STP-compatible mode.

rstp

: Configures an MSTP-enabled switch to work in RSTP mode.

mstp

: Configures an MSTP-enabled switch to work in MSTP mode.

Description

Use the

stp mode

command to configure the MSTP work mode of the switch.

Use the

undo stp mode

command to restore the MSTP work mode to the default setting.

By default, an MSTP-enabled switch works in MSTP mode.
Related commands:

stp mcheck

and

stp enable

Examples

# Configure the MSTP-enabled switch to work in STP-compatible mode.

<Sysname> system-view

[Sysname] stp mode stp

stp no-agreement-check

Syntax

stp no-agreement-check
undo stp no-agreement-check

View

Layer 2 Ethernet interface view, port group view, Layer 2 aggregate interface view

Default level

2: System level

Parameters

None

Description

Use the

stp no-agreement-check

command to enable No Agreement Check on the port(s).

Use the

undo stp no-agreement-check

command to disable No Agreement Check on the port(s).

By default, No Agreement Check is disabled.

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды