manualshive.com logo in svg

H3C S5120-EI Series, Справочник по командам

Поделиться
Скачать
H3C S5120-EI Series Скачать руководство пользователя страница 56

44 

•

 

For a Gigabit port, the value range is 1 to 1000000. 

•

 

For a 10-Gigabit port, the value range is 1 to 10000000.  

Description 

Use the 

unicast-suppression 

command to set the unknown unicast suppression threshold on an Ethernet 

interface view or a group of Ethernet interfaces in port group view. 
Use the 

undo unicast-suppression 

command to restore the default. 

By default, Ethernet interfaces do not suppress unknown unicast traffic. 
If you execute this command in Ethernet interface view, the configurations take effect only on the current 

interface. If you execute this command in port-group view, the configurations take effect on all ports in the 

port group. 
When unknown unicast traffic exceeds the threshold you configure, the system discards unknown unicast 

packets until the unknown unicast traffic drops below the threshold. 

 

 

NOTE: 

•

 

If you set different unknown unicast suppression thresholds in Ethernet interface view or port-group view
multiple times, the one configured last takes effect. 

•

 

For a particular type of traffic, configure either storm suppression or storm control, but not both. If both
of them are configured, you may fail to achieve the expected storm control effect. 

 

Examples 

# Set the unknown unicast threshold to 20% on Ethernet interface GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] unicast-suppression 20 

# Set the unknown unicast threshold to 20% on all ports of port group 

group1

. 

<Sysname> system-view 

[Sysname] port-group manual group1 

[Sysname-port-group-manual-group1] group-member gigabitethernet 1/0/1 

[Sysname-port-group-manual-group1] group-member gigabitethernet 1/0/2 

[Sysname-port-group-manual-group1] unicast-suppression 20 

virtual-cable-test 

Syntax 

virtual-cable-test 

View 

Ethernet interface view 

Default level 

2: System level 

Parameters 

None 

Содержание S5120-EI Series



















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды