H3C S5120-EI Series Скачать руководство пользователя страница 61

Страница: 61 / 242

Field Description

second.

•

bits/sec

indicates the average number of bits received per

second.

Last 300 seconds output: 0 bytes/sec, 0

bits/sec, 0 packets/sec

Average output rate over the last 300 seconds, where:

•

packets/sec

indicates the average number of packets sent per

second.

•

bytes/sec

indicates the average number of bytes sent per

second.

•

bits/sec

indicates the average number of bits sent per second.

0 packets input, 0 bytes, 0 drops

Total number and size (in bytes) of the input packets of the
interface and the number of the dropped packets

0 packets output, 0 bytes, 0 drops

Total number and size (in bytes) of the output packets of the
interface and the number of the dropped packets

The brief information of interface(s) under
route mode

Brief information about Layer 3 interfaces

Link: ADM - administratively down; Stby -
standby

Link status:

•

ADM – The interface has been administratively shut down. To
recover its physical state, perform the

undo shutdown

command.

•

Stby – The interface is operating as a backup interface.

Protocol: (s) - spoofing

If the network layer protocol state of an interface is shown as UP,
but its link is an on-demand link or not present at all, its protocol

attribute includes the spoofing flag (an

in parentheses).

Interface

Abbreviated interface name

Link

Physical link state of the interface, which can be:

•

UP – The link is up.

•

ADM – The link has been administratively shut down. To
recover its physical state, perform the

undo shutdown

command.

Protocol

Protocol connection state of the interface, which can be UP,
DOWN, or UP(s).

Main IP

The main IP address of the interface

Description

Description of the interface

Cause

The cause of a DOWN physical link. If the port has been shut
down with the

shutdown

command, this field displays

Administratively

. To restore the physical state of the interface,

use the

undo shutdown

command.

NOTE:

Because the S5120-EIseries Ethernet switches do not count the average input/output rate or input/output
packets of a loopback interface, these fields are displayed as “0” in the

display interface loopback

command output.

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды