manualshive.com logo in svg

H3C S5120-EI Series, Справочник по командам

Поделиться
Скачать
H3C S5120-EI Series Скачать руководство пользователя страница 34

22 

By default, Rx flow control is disabled on Ethernet interfaces. 
With the 

flow-control receive enable

 command configured, an interface can receive, but not send flow 

control frames. When the interface receives a flow control frame from its peer, it suspends sending 
packets to the peer. When traffic congestion occurs on the interface, it cannot send flow control frames 

to the peer. 
To handle unidirectional traffic congestion on a link, configure the 

flow-control receive enable

 command 

at one end, and the 

flow-control

 command at the other. To enable both ends of the link to handle traffic 

congestion, configure the 

flow-control

 command at both ends. 

Examples 

# Enable Rx mode generic flow control on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] flow-control receive enable 

flow-interval 

Syntax 

flow-interval 

interval 

undo flow-interval 

View 

Ethernet interface view 

Default level 

2: System level 

Parameters 

interval

: Sets a statistics polling interval, in seconds. It ranges from 5 to 300 and must be a multiple of 

5. 

Description 

Use the 

flow-interval 

command to set the interface statistics polling interval. 

Use the 

undo flow-interval 

command to restore the default interval. 

The default interface statistics polling interval depends on your device model. 

Examples 

# Set the statistics polling interval to 100 seconds on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] flow-interval 100 

group-member 

Syntax 

group-member

 interface-list

 

undo group-member

 interface-list

 

Содержание S5120-EI Series



















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды