H3C S5120-EI Series Скачать руководство пользователя страница 32

Страница: 32 / 242

Field Description

•

—

The port sends threshold event traps.

•

Off

—

The port does not send threshold event traps.

Log

Status of the storm control threshold event log switch:

•

—

The port sends threshold event log messages.

•

Off

—

The port does not send threshold event log messages.

Swinum

Number of times the forwarding state of the interface changes.
When the

Swi-num

count reaches 65,535, it resets automatically.

duplex

Syntax

duplex

{

auto

full

half

}

undo duplex

View

Ethernet interface view

Default level

2: System level

Parameters

auto

: Sets the interface to operate in auto-negotiation mode.

full

: Sets the interface to operate in full duplex mode.

half

: Sets the interface to operate in half-duplex mode. This keyword is not available for the optical port

of an SFP port, or electrical (copper) Ethernet ports operating at 1000 Mbps

Description

Use the

duplex

command to set the duplex mode for an Ethernet interface.

Use the

undo duplex

command to restore the default duplex mode of the Ethernet interface.

By default, Ethernet interfaces operate in auto-negotiation mode.
Related commands:

speed

Examples

# Configure interface GigabitEthernet 1/0/1 to operate in full-duplex mode.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] duplex full

flow-control

Syntax

flow-control
undo flow-control

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды