H3C S5120-EI Series Скачать руководство пользователя страница 220

Страница: 220 / 242

208

Port VLAN ID(PVID): 1

Port and protocol VLAN ID(PPVID) : 1

Port and protocol VLAN supported : Yes

Port and protocol VLAN enabled : No

VLAN name of VLAN 1: VLAN 0001

Auto-negotiation supported : Yes

Auto-negotiation enabled : Yes

OperMau : speed(1000)/duplex(Full)

Power port class : PD

PSE power supported : No

PSE power enabled : No

PSE pairs control ability : No

Power pairs : Signal

Port power classification : Class 0

Link aggregation supported : Yes

Link aggregation enabled : No

Aggregation port ID : 0

Maximum frame Size: 1536

# Display the LLDP information sent from all the neighboring devices in the form of a list.

<Sysname> display lldp neighbor-information list

System Name Local Interface Chassis ID Port ID

System1 GE1/0/1 000f-e25d-ee91 GigabitEthernet1/0/5

System2 GE1/0/2 000f-e25d-ee92 GigabitEthernet1/0/6

System3 GE1/0/3 000f-e25d-ee93 GigabitEthernet1/0/7

Table 47

Output description

Field Description

LLDP neighbor-information of port 1 LLDP information received through port 1.

Update time

Time when LLDP information about a neighboring device is last updated.

Chassis type

Chassis information:

•

Chassis component

•

Interface alias

•

Port component

•

MAC address

•

Network address (the IP address type, such as

ipv4

)

•

Interface name

•

Locally assigned (indicating the local configuration)

Chassis ID

ID that identifies the LLDP sending device, which can be a MAC address,
a network address, an interface or some other value depending on the

chassis type.

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды