H3C S5120-EI Series Скачать руководство пользователя страница 155

Страница: 155 / 242

143

View

User view

Default level

2: System level

Parameters

vlan-interface-id

: Specifies a VLAN interface number.

Description

Use the

reset counters interface vlan-interface

command to clear the statistics on a VLAN interface.

Before collecting the traffic statistics within a specific period of time on an interface, you need to clear the

existing statistics first.

•

If the

vlan-interface-id

argument is not specified, this command clears the statistics of all VLAN

interfaces.

•

If the

vlan-interface-id

argument is specified, this command clears the statistics of the specified

VLAN interface.

Related commands:

display interface vlan-interface

Examples

# Clear the statistics on VLAN-interface 2.

<Sysname> reset counters interface vlan-interface 2

shutdown

Syntax

shutdown
undo shutdown

View

VLAN interface view

Default level

2: System level

Parameters

None

Description

Use the

shutdown

command to shut down a VLAN interface.

Use the

undo shutdown

command to bring up a VLAN interface.

By default, a VLAN interface is up except when all ports in the VLAN are down.
You can use the

undo shutdown

command to bring up a VLAN interface after configuring related

parameters and protocols for the VLAN interface. When a VLAN interface fails, you can shut down the

interface with the

shutdown

command and then bring it up with the

undo shutdown

command. In this

way, the interface may resume.
The state of any Ethernet port in a VLAN is independent of the VLAN interface state.

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды