manualshive.com logo in svg

H3C S5120-EI Series, Справочник по командам

Поделиться
Скачать
H3C S5120-EI Series Скачать руководство пользователя страница 156

 

144 

Examples 

# Shut down VLAN-interface 2 and then bring it up. 

<Sysname> system-view 

[Sysname] interface vlan-interface 2 

[Sysname-Vlan-interface2] shutdown 

[Sysname-Vlan-interface2] undo shutdown 

vlan 

Syntax 

vlan

 { 

vlan-id1 

[

 to

 vlan-id2 

] | 

all

 } 

undo vlan

 

{ 

vlan-id1 

[

 to

 vlan-id2 

] | 

all

 } 

View 

System view 

Default level 

2: System level 

Parameters 

vlan-id1

, 

vlan-id2

: Specifies a VLAN ID, ranging from 1 to 4094. 

vlan-id1

 

to

 

vlan-id2

: Specifies a VLAN range.

 

all

: Creates or removes all VLANs except reserved VLANs. The keyword is not supported when the 

maximum number of VLANs that can be created on a device is less than 4094. 

Description 

Use the 

vlan 

vlan-id 

command to create a VLAN and enter its view or enter the view of an existing VLAN.  

Use the 

vlan

 

vlan-id1

 to

 vlan-id2 

command to create a range of VLANs specified by 

vlan-id1 

to

 

vlan-id2

, 

except reserved VLANs. 
Use the 

undo vlan 

command to remove the specified VLAN(s). 

 

 

NOTE: 

•

 

As the default VLAN, VLAN 1 cannot be created or removed.  

•

 

You cannot create or remove reserved VLANs reserved for specific functions. 

•

 

You cannot use the 

undo vlan

 command to directly remove reserved VLANs, voice VLANs, 

management VLANs, dynamic VLANs, VLANs configured with QoS policies, control VLANs configured

for Smart Link, RRPP protected VLANs, or remote probe VLANs configured for port mirroring. To remove
these VLANs, remove related configurations first.  

•

 

If an isolate-user-VLAN and a secondary VLAN are associated with each other with the 

isolate-user-vlan

 command, the isolate-user-VLAN or secondary VLAN cannot be removed unless the

association is removed first. 

 

Related commands: 

display vlan

. 

Examples 

# Enter VLAN 2 view. 

<Sysname> system-view 

[Sysname] vlan 2 

Содержание S5120-EI Series



















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды