manualshive.com logo in svg

H3C S5120-EI Series, Справочник по командам

Поделиться
Скачать
H3C S5120-EI Series Скачать руководство пользователя страница 42

30 

View 

System view 

Default level 

2: System level 

Parameters 

time

: Sets the loopback detection interval, ranging from 5 to 300 seconds.

 

Description 

Use the 

loopback-detection interval-time 

command to set the loopback detection interval. 

Use the

 undo loopback-detection interval-time 

command to restore the default loopback detection 

interval. 
By default, the loopback detection interval is 30 seconds. 
Related commands: 

display loopback-detection

. 

Examples 

# Set the loopback detection interval to 10 seconds. 

<Sysname> system-view 

[Sysname] loopback-detection interval-time 10 

loopback-detection multi-port-mode enable 

Syntax 

loopback-detection multi-port-mode enable 
undo loopback-detection multi-port-mode enable 

View 

System view 

Default level 

2: System level 

Parameters 

None 

Description 

Use the

 loopback-detection multi-port-mode enable

 command to enable multi-port loopback detection 

mode. 
Use the 

undo loopback-detection multi-port-mode enable

 command to restore the default. 

By default, multi-port loopback detection mode is disabled. 
When detecting a loop between two interfaces, the system takes the following actions on the looped 

interface: 

•

 

If the looped interface is an access interface: perform the configured protective action, send traps 

to the terminals, and delete all MAC address entries of the interface. 

•

 

If the looped interface is a trunk or hybrid interface:  send  traps  to  the  terminals.  If  loopback 

detection control is enabled, perform the configured protection action on the looped interface, and 
delete all MAC address entries of the interface. 

Содержание S5120-EI Series



















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды