H3C S5120-EI Series Скачать руководство пользователя страница 176

Страница: 176 / 242

164

protocol-vlan

Syntax

protocol-vlan

[

protocol-index

] {

ipv4 | ipv6

ipx

{

ethernetii

llc

raw

snap

} |

mode

{

ethernetii

etype

etype-id

llc

{

dsap

dsap-id

[

ssap

ssap-id

]

ssap

ssap-id

} |

snap

etype

etype-id

} }

undo protocol-vlan

{

protocol-index

[

protocol-end

] |

all

}

View

VLAN view

Default level

2: System level

Parameters

: Specifies the AppleTalk based VLAN.

ipv4

: Specifies the IPv4 based VLAN.

ipv6

: Specifies the IPv6 based VLAN.

ipx

: Specifies the IPX based VLAN. The keywords

ethernetii

llc

raw

, and

snap

are encapsulation

formats for IPX.

mode

: Configures a user-defined protocol template for the VLAN, which could also have the following

encapsulation formats:

ethernetii

llc

raw

, and

snap

ethernetii etype

etype-id

: Specifies to match Ethernet II encapsulation format and the corresponding

protocol type values. The

etype-id

argument is the protocol type ID of inbound packets, ranging from

0x0600 to 0xffff (excluding 0x0800, 0x809b, 0x8137, and 0x86dd).

llc

: Specifies to match the

llc

encapsulation format.

dsap

dsap-id

: Specifies the destination service access point, ranging from 00 to 0xff.

ssap

ssap-id

: Specifies the source service access point, ranging from 00 to 0xff.

snap etype

etype-id

: Specifies to match SNAP encapsulation format and the corresponding protocol type

values. The

etype-id

argument is the Ethernet type of inbound packets, ranging from 0x0600 to 0xffff

(excluding

ipx snap

under the

snap

encapsulation format).

protocol-index

: Specifies a protocol template index. System will automatically assign an index if this

parameter is not specified.

protocol-end

: Specifies the end protocol index. The

protocol-end

argument must be greater than or

equal to the

protocol-index

argument

all

: Specifies to remove all the protocols bound to the current VLAN.

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды