H3C S5120-EI Series Скачать руководство пользователя страница 183

Страница: 183 / 242

171

Isolate-user-VLAN configuration commands

display isolate-user-vlan

Syntax

display isolate-user-vlan

[

isolate-user-vlan-id

] [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

isolate-user-vlan-id

: Specifies an isolate-user-VLAN ID, ranging from 1 to 4094.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see the

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, which is a case sensitive string of 1 to 256

characters.

Description

Use the

display isolate-user-vlan

command to display the mapping between an isolate-user-VLAN and

secondary VLAN(s).
Related commands:

isolate-user-vlan

and

isolate-user-vlan enable

Examples

# Display the mapping between an isolate-user-VLAN and secondary VLANs.

<Sysname> display isolate-user-vlan

Isolate-user-VLAN VLAN ID : 2

Secondary VLAN ID : 3 4

VLAN ID: 2

VLAN Type: static

Isolate-user-VLAN type : isolate-user-VLAN

Route Interface: configured

IP Address: 1.1.1.1

Subnet Mask: 255.255.255.0

Description: VLAN 0002

Name: VLAN 0002

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды