H3C S5120-EI Series Скачать руководство пользователя страница 169

Страница: 169 / 242

157

Default level

2: System level

Parameters

None

Description

Use the

mac-vlan enable

command to enable MAC address-based VLAN on a port.

Use the

undo mac-vlan enable

command to disable MAC address-based VLAN on a port.

By default, MAC address-based VLAN is disabled on a port.

Examples

# Enable MAC address-based VLAN on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname–GigabitEthernet1/0/1] mac-vlan enable

mac-vlan mac-address

Syntax

mac-vlan mac-address

mac-address

vlan

vlan-id

[

priority

pri

]

undo mac-vlan

{

all

mac-address

mac-address

] |

vlan

vlan-id

}

View

System view

Default level

2: System level

Parameters

mac-address

mac-address

: Specifies a MAC address.

vlan

vlan-id

: Specifies a VLAN ID, ranging from 1 to 4094.

priority

pri

: Specifies the 802.1p priority value corresponding to the specified MAC address. This

argument ranges from 0 to 7.

all

: Removes all the static MAC address-to-VLAN entries.

Description

Use the

mac-vlan mac-address

command to associate the specified VLAN and priority value with the

specified MAC addresses.
Use the

undo mac-vlan

command to remove the association.

Two MAC address-to-VLAN entry tables exist in a device. One table contains the MAC address-to-VLAN

entries configured with the

mask

keyword specified. A MAC address-to-VLAN entry of this type describes

the relationship between a group of MAC addresses and a VLAN, and a priority value. Another table

contains the MAC address-to-VLAN entries configured without the

mask

keyword specified. A MAC

address-to-VLAN entry of this type describes the relationship between a single MAC address and a

VLAN, and a priority value. The system adds/removes MAC address-to-VLAN entries to/from the two
tables according to the configuration.

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды