manualshive.com logo in svg

H3C S5120-EI Series, Справочник по командам

Поделиться
Скачать
H3C S5120-EI Series Скачать руководство пользователя страница 72

 

60 

View 

System view 

Default level 

2: System level 

Parameters 

blackhole

: Specifies destination blackhole MAC address entries. These entries do not age, but you can 

add or remove them. The packets whose destination MAC addresses match destination blackhole MAC 

address entries are dropped. 

mac

-

address

: Specifies a MAC address in the format of H-H-H, where 0s at the beginning of each H 

(16-bit hexadecimal digit) can be omitted. For example, inputting “f-e2-1” indicates that the MAC 

address is “000f-00e2-0001”. 

vlan 

vlan

-

id

: Specifies an existing VLAN to which the Ethernet interface belongs, where 

vlan-id

 is the 

specified VLAN ID, in the range 1 to 4094. 

dynamic

: Specifies dynamic MAC address entries. Aging time is set for these entries. 

static

: Specifies static MAC address entries. These entries do not age, but you can add or remove them. 

interface 

interface

-

type interface

-

number

: Specifies an outbound interface by its type and number. 

Description 

Use the 

mac-address 

command to add or modify a MAC address entry. 

Use the 

undo mac-address 

command to remove one or all MAC address entries. 

A static or blackhole MAC address entry will not be overwritten by a dynamic MAC address entry. A 

dynamic MAC address entry can be overwritten by a static or blackhole MAC address entry.  
If you execute the 

undo mac-address

 command without specifying any parameters, this command 

deletes all unicast MAC address entries and static multicast MAC address entries. 
You can delete all the MAC address entries (including unicast MAC address entries and static multicast 

MAC address entries) of a VLAN, or you can choose to delete its dynamic, static, or blackhole MAC 
address entries only. You can single out some ports and delete the corresponding unicast MAC address 

entries, but not the corresponding static multicast MAC address entries. 
The MAC address entries configuration cannot survive a reboot unless you save it. The dynamic MAC 

address table entries will be lost, whether you save the configuration or not. 
Related commands: 

display mac-address

. 

Examples 

# Add a static entry for MAC address 000f-e201-0101. All frames destined to this MAC address are sent 
out of port GigabitEthernet1/0/1 which belongs to VLAN 2. 

<Sysname> system-view 

[Sysname] mac-address static 000f-e201-0101 interface GigabitEthernet1/0/1 vlan 2 

mac-address mac-learning disable 

Syntax 

mac-address mac-learning disable 
undo mac-address mac-learning disable 

Содержание S5120-EI Series



















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды