GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 71

Страница: 71 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

heating", the thermistor temperature of temperature sensor is lower than the limit temperature, the basic

heating restarts. Additional heating has a similar situation. Note that the temperature limiter's influence

on the set temperature, the heating temperature will not reach the set temperature higher than the limit.

4.13 Parameter window "Air Condition"

These parameters is used to set the air conditioning control. There are two object types: 1bit or 1byte. If 1bit

type is selected, control commands are sent by 1bit objects, and different objects corresponds to a different

commands. If 1byte type is selected, control command sent by 1byte object, different 1 byte value corresponds to

a different commands. These control commands similar to the air-conditioning on the remote control commands,

Users can learn the air conditioner remote control commands to the infrared transmitter module, configure the

Thermostat with corresponding parameters,

and then users can send through these commands by operating the

Thermostat to control the infrared transmitter module. Under this setting, the 4 room temperature modes invalid

and can not be switched, only display comfort mode. The "Set Key" is only used to switch heating and cooling.

Figure 4.13 parameter window "Air Condition"

Parameter "Setpoint"
Options: 16- 32

This option is to set the setpoint temperature the air-conditioner. It is used to achieve thermostatic

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды